联系我们
有机硅耐热面漆 300
关键词：
有机硅耐热面漆 300
- 产品描述
-
THERMO 300 FINISH 有机硅耐热面漆 300
PRODUCT DESCRIPTION A heat resisting paint based on modified silicone resin and aluminium powder.
产品简介 由改性有机硅树脂与铝粉组成的耐热涂料。RECOMMENDED USE For long-term protection of hot pipelines, exhaust pipes, smoke stacks and other hot surfaces at temperatures up to 300℃ and 350℃ at a short time.
用途 长效保护温度高达300℃（瞬时温度350℃）的热管道、排气管、烟囱和其它热表面。FEATURES Excellent heat resistance (Up to 300℃)
产品特性 极好的耐热性（到300℃）
Good weathering resistance
极好的耐候性
Good applicability
极好的施工性能PHYSICALPROPERTIES
基本数据Color Silver
颜色 银色
Finish Gloss
光泽 有光
Volume Solids
体积固体份 25%
Flash Point Greater than 27℃
闪点 27℃以上
Film thickness Dry : 20-30 microns/coat Wet :80-120microns/coat
涂装膜厚 干膜: 20-30 微米/道 湿膜:80-120 微米/道
Theoretical Coverage 0.082kg/m2/20microns
理论涂布率 0.082 千克/平方米/20 微米Practical coverage depending on surface conditions, environment, applications, etc.
实际涂布率与表面处理, 外界环境, 施工方法等多种因素有关。APPLICATION
施工
Application Temperature
施工温度 -5℃-40℃
Mixing Mix thoroughly with power agitator
混合 使用动力工具搅拌均匀
Mixing Ratio One component coating
混合比例 单组份涂料
ApplicationMethods Airless spray, air spray, brush and roller
施工方法 无气喷涂、空气喷涂、刷涂、滚涂Airless spray 无气喷涂
Nozzle tip 喷嘴尺寸0.33mm-0.43mm
Nozzle pressure 出口压力≥10Mpa
Thinning ratio 稀释比率0-5% by weight（重量比）Brush/Roller 刷涂、滚涂
Thinning ratio 稀释比率0-5% by weight（重量比）Thinner Paint Thinner X
稀释剂 稀释剂X
Drying time & Temperature 温度5℃ 20℃ 30℃
Overcoating interval Surface dry 指触干燥3hrs 1hr 1hr干燥时间&涂装间隔 Touch dry 半硬干燥5hrs 3hrs 3hrs
Min. interval 最小涂装间隔16hrs 12hrs 8hrs
Max. interval 最大涂装间隔
Full cure: must bake in 200℃-250℃ for 1hr
完全固化：必须在200℃~250℃烘烤1 小时Typical undercoat THERMO 300 PRIMER, SD ZINC PRIMER 2000
适用下涂 有机硅耐热底漆300，无机富锌底漆2000
Typical topcoat
适用上涂STORAGE Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept tightly closed.
贮存于干燥阴凉的环境中，远离热源及火源。包装桶必须保持封闭。
Shelf life 12months from date of production (25℃)
贮存期限 自生产之日起12 个月（25℃）
DISCLAIMER 提请注意
The information given on this sheet is to the best of our knowledge and accurate at the time of issuing. Since conditions of use are beyond the manufacturer’s control,information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非我方所能控制，此中信息不含担保，即仅在选取产品上对买方负责。由于我公司产品及生产工艺的不断发展，本说明书的内容也会随时进行更改，此中所有信息均以我方确认为主。产品使用前，请确认所持说明书为最新版本。www.kansai.com.cn
产品询价
联系方式
